1 files changed, 0 insertions, 143 deletions
diff --git a/MakefileBasedBuild/Atmel/sam3x/sam3x-ek/libraries/usb_device/class/hid/device/generic/example/atxmega128b1_xmega_b1_xplained/ui.c b/MakefileBasedBuild/Atmel/sam3x/sam3x-ek/libraries/usb_device/class/hid/device/generic/example/atxmega128b1_xmega_b1_xplained/ui.c
deleted file mode 100644
index c0d18ce..0000000
--- a/MakefileBasedBuild/Atmel/sam3x/sam3x-ek/libraries/usb_device/class/hid/device/generic/example/atxmega128b1_xmega_b1_xplained/ui.c
+++ /dev/null
@@ -1,143 +0,0 @@
-/**
- * \file
- *
- * \brief User Interface
- *
- * Copyright (C) 2009 Atmel Corporation. All rights reserved.
- *
- * \page License
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * 1. Redistributions of source code must retain the above copyright notice,
- * this list of conditions and the following disclaimer.
- *
- * 2. Redistributions in binary form must reproduce the above copyright notice,
- * this list of conditions and the following disclaimer in the documentation
- * and/or other materials provided with the distribution.
- *
- * 3. The name of Atmel may not be used to endorse or promote products derived
- * from this software without specific prior written permission.
- *
- * 4. This software may only be redistributed and used in connection with an
- * Atmel AVR product.
- *
- * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
- * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
- * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
- * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
- * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
- * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
- * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
- * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
- * DAMAGE.
- */
-
-#include "compiler.h"
-#include "conf_usb.h"
-#include "udc.h"
-#include "udi_hid_generic.h"
-#include "board.h"
-#include "led.h"
-#include "ui.h"
-
-void ui_init(void)
-{
-}
-
-void ui_powerdown(void)
-{
-}
-
-void ui_wakeup_enable(void)
-{
-	PORT_t *port;
-	// Configure pin change interrupt for asynch. wake-up on button pin.
-	ioport_configure_pin(GPIO_PUSH_BUTTON_0,
-			IOPORT_DIR_INPUT | IOPORT_PULL_UP);
-	port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0);
-	port->INT0MASK = 0xFF;
-	port->INTCTRL = PORT_INT0LVL_LO_gc;
-}
-
-void ui_wakeup_disable(void)
-{
-	PORT_t *port;
-	port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0);
-	port->INT0MASK = 0x00;
-}
-
-// Interrupt on "pin change" from switch to do wakeup on USB
-// Note:
-// This interrupt is enable when the USB host enable remotewakeup feature
-// This interrupt wakeup the CPU if this one is in idle mode
-ISR(PORTE_INT0_vect)
-{
-	PORT_t *port;
-	port = ioport_pin_to_port(GPIO_PUSH_BUTTON_0);
-	port->INTFLAGS = 0x01;	// Ack interrupt
-	// It is a wakeup then send wakeup USB
-	udc_wakeup();
-}
-
-void ui_wakeup(void)
-{
-}
-
-void ui_process(uint16_t framenumber)
-{
-}
-
-void ui_led_on(uint8_t led_num)
-{
-	switch (led_num) {
-	case 1:
-		LED_On(LED0_GPIO);
-		break;
-	case 2:
-		LED_On(LED1_GPIO);
-		break;
-	case 3:
-		LED_On(LED2_GPIO);
-		break;
-	case 4:
-		LED_On(LED3_GPIO);
-		break;
-	}
-}
-
-void ui_led_off(uint8_t led_num)
-{
-	switch (led_num) {
-	case 1:
-		LED_Off(LED0_GPIO);
-		break;
-	case 2:
-		LED_Off(LED1_GPIO);
-		break;
-	case 3:
-		LED_Off(LED2_GPIO);
-		break;
-	case 4:
-		LED_Off(LED3_GPIO);
-		break;
-	}
-}
-
-bool ui_button(void)
-{
-	return gpio_pin_is_low(GPIO_PUSH_BUTTON_0);
-}
-
-/**
- * \defgroup UI User Interface
- *
- * Human interface on XMEGA-B1 Xplain:
- * - RED led close to USB connector is always on after firmware startup
- * - Led 0 to 3 are controlled by USB Host application
- * - Switch 0 events are reported to USB Host application
- * - Switch 0 can be used to wakeup USB Host in remote wakeup mode.
- */